◆ Price11,760 yen(Because domestic specifications have a matte part14,260 yenIt will be)◆ Set contents
● Paint (main agent)
・ Metallic Maroon 450g
・ Line orange 225g
・ Line red 225g
● 120g of curing agent
● Light solution 1L
● Rice paper
● Weighing poly cup
● Painting manual●GS400II type drawingAppears※In the case of Japan, a glossy black 250g set (with a curing agent, with a thin liquid) is attached.. +2,500 yen
note)As a guide to the amountWith this paint set, the amount of GS exterior can be applied.
Tank, side cover, tail cowl, fender (light case, oil tank, etc. depending on the model)
In addition, I think that the failure is calculated a lot, so I think that it can be repainted enough if it is about one tank.
◆ Suffessor, clear price list(Sold separately)※Clear and white saffocar are sold separately
・ Clear 500g set 2713 yen
・ Clear 1 km set 4580 yen
・ White safeser 750G set 3285 yen
・ White safeser 1, 5 km set 5181 yen ※There is also a curing agent, thin liquid, stiff paper, and weighing poly cup
If you wish, please contact us when you make a successful bid, "Clear" or "Suffessor wishes".
Also, please click here when purchasing in the auction.◆ White Saféeser ◆◆ Urethane clear ◆
|
| About the composition |
This paint is a 2 -liquid type (painted with a curing agent), so add a curing agent.
is needed
For the composition, it becomes a curing agent 1 for paint 8 (8: 1)
For example, in the case of paint 80g (CC), it will be 10g (CC).
It is a thin liquid (thinner), but this depends on the temperature,
If the temperature is 20 degrees, put about 6-8 for the paint 10.
Therefore, paint 80g (cc) hardening agent 10g (CC): Thin liquid 50-70g (CC) is required.
When the blends are over, they will be painted, but be sure to use paper or cardboard.
Please apply it after trial painting. The above formulation is a standard, so fine -tuning is required◎When a trial coat, the color of the edge of the paper accumulates or thin, there are many thin fluids◎If the thread is pulled from the spray gun, and the paper becomes rough.
There are few thin liquids, so please add
Detailed composition and procedures are painted manuals, etc.Homepage procedureBy referring to
If you still don't understand, please email or TEL at any time.※It is a curing agent, but depending on the specific gravity of the paint
There is a certain amount of setting setting, so if it is a small amount of error,
No problem. However, if it is few, it will not dry (it does not solidify)
Please note that there are cases※The components of each manufacturer are different for urethane paints. Setting and curing agent and
Please note that the composition will change※The composition of a thin liquid is less when the temperature is low, and the higher it is.
Also, it depends on the color, so be sure to use paper or cardboard.
Please apply for a trial painting※Paints are not good for the body, so be sure to masks and well -ventilated places or
Please paint using a device (such as a booth) to put the paint out
|
| ★ About candy painting |
I think the candy color is the origin of the old candy (candy) wrapping paper.
The translucent color is wrapped up on the silver paper to create a beautiful unique look.
Similarly, even with paint, translucent paint on silver(Transparent colorBy applying)
Unlike the color of the conventional paint, the silver shines through the shining place (bright place),
In places that do not glow (dark places), the silver does not shine, so it feels dark. The basic candy color is translucent color on silver(Red, blue, yellow. Green etc.)of
Apply it, but apply it to change the undercoated silver to gray metallic or colored metallic.
There is also a way to paint. (If you add color to the undercoat, it may be called a cocktail)※If the undercoat is colored, the color unevenness is less noticeable and it is easy to apply. In addition, the color clear of the top coat
If you mix various colors, it will tend to become cloudy or uneven color, so coloring the lower color will improve workabilityIn addition, there is also a candy type paint using three colors of paint. For example, the base of the ZII fireball is painted with black and a coarse metallic (pearl) is scattered on it.
By applying the orange color clear, the black part gives a bitterness and the metallic part
Give brightness and become a unique shade.(Orange color clear looks dark so it looks brown)It's not so much with recent motorcycles,Old KawasakiThere are many ways to paint
Because of this kind of painting, normal candy type and cocktail type require two colors of paint2 coats,A three -color paint is required for how to apply it like a fireball3 coatWe sayRegardless of silverFirst of all, the metallic is beautifully aluminum powder (pearl powder)Laired neatlyis needed
If you apply it in the same way as the solit paint, you will get a lump of aluminum powder and apply the color clearThat partbut
It becomes uneven and dark part and bright part are formed, so it does not become beautiful paintpointAs a little bit, squeeze the paint out (the second adjustment knob from the top of the spray gun).
Apply the movement of your hands much faster. It's not so difficult, butThe important thing is hand movementsFasterThe point is that once you get used to it, you can paint with just your hands movements without squeezing the paint※It is necessary to adjust around that area because it will be rough if there are few scinners of the paintAfter drying(Leave 3 hours or more)Apply color clearRegarding color clearThe first important thing when applying color clear,Do not add garbage as much as possibleIt is to paint like
Especially if there is a lot of garbage in the silver, the color clear will accumulate around the garbage and it will be black.
The finish of the corner will be ruined. Because it is impossible to completely eliminate garbage
Pay as clean as possible by air, so that there is no static electricity on days when the wind is as low as possible(Sprinkle the cloth or water on the ground, etc.)Please be ready to paint
Next will be blended. If it is a compound ... If the amount of thin liquid is small and the paint is hard, the color clear
It becomes rugged and the particles become rough and cause uneven color.. Make the paint softer as much as possibleTemperature 20 degreesIs a rough guideLight liquid about 100 to 100 to 100 for paintPut
The lower the temperature, the less the thinner, and the higher the temperature, the more thinner.
The amount of thin liquid depends on the color component, so be sure to try and adjust the paper.Please enter this paint
★ Trial -painted symptoms·Color accumulates on the edge of the paper・ ・ ・ ・ ・ ・ There are many thinner, or I put too much paint at once (Adjustment of paint))
・The surface is rough and darkThere are few thinner or small air pressure
・The surface is Madara······················································································■Color clear (Candy colored) Painting procedure* The photo below is for candy blueI will paint if it is well blended, but the candy is basicallyPut it thinlyIt is better to go. If the undercoat is colored or if the top coat paint may be dark,
Unless otherwise, the color of the top coatWhen thin or beautifulI will apply it again
First, drop the air pressure and add a light color to the difficult part. If you paint the part that is difficult to paint later, you can force it
I try to add color and drop it, or partially darkens, so it doesn't get well.
If the fine part is coloredPut on about 5 minutesThen apply the whole thinly, for example, at this time
Light pink for candy red, light blue feeling for candy blue. If it is too colored, it will darken and darken when applied overlaid. If you apply the whole thinlyPut on about 5 minutesPlease apply the whole after all. I think that this state is colored to some extent. alreadyStore for about 5 minutesThe part that is not painted
If there is (thin part), apply that part and color it.
It is completed in this process, but if it is still thin or if there is a part that is not painted, leave the time again.
Please paint. This painting method isThere is a little lusterIt's better than just hangingThe gloss is clearSo you don't have to worry too much
After this, apply clear and complete. The detailed procedure is posted on our website.
Click below. Also for the paint setPainting manualIt will be
◆Overall painting procedure◆Candy color painting procedure◆Masking procedure※This is the paint procedure of our paint for how to apply and dry time. What are repair paints for cars?
Since the ingredients, drying time, and characteristics are different, please refer to our painting method
|
| ★ Attached to masking |
I think masking is the most troublesome of old carsThe point of masking is・ Make the dimensions properly (first create a center that is the center)
・ Paste the tape properly without gaps
・ Prepare a cut cutter
・ Do not add garbage to the tape
・ Do the masking thing after dry (the trace of the tape is attached)
・ Do it in a beautiful environment
・ Do it carefully over time★ Convenient thing when maskingThe photo like the aboveI think it will be necessary(Some models are not needed)Also,Upper left photoIt is easy to mask while referring to the drawing attached to the paint set of(Dimensions are issued from edges, tank cocks, emblem mounting parts, etc.)For more information, please refer to the masking procedure on our website.
(The procedure is posted in detail)
・Masking procedure (FX E4)・ Masking procedure (fireball)Basically, masking is easier because the masking area is smaller by painting from a small area.
Considering the steps of the line, the candy paint is the stage of two colors, so it is better to apply it first.
It will look better(It is better to have a lower step)E4 in the photo belowThere is a blur, so I will start with the first time
Then in order, the color of the blur of the blurring, the black of the line → the line of the line → and finally the base
It is the procedure to apply Luminus Gun Blue. |
|
