- Blumes (R) base over drive
BLUMES (R) (Blooms) has been developed as a base overdrive of the popular TS pedal plumes among various players since the announcement.. Like plumes, the base overdrive Blumes, which is equipped with a 3 -clipping mode and specializes in the bass part, has doubled the amount of gains, the bass output and the response are specialized in the base band, and the distortion from the deep low frequency is clearly output. To do. Answer the expectations of all bassists who need distortion in dynamics and headrooms that respond to the fine movements at hand.. It is ideal for giving a more three -dimensional feeling and biting feeling to the vacuum tube base amplifier used, and this Brooms tuning also produces modern distortions that are effective against bass, such as multi -string guitars and drop tuning guitars.. Control
Gain: Setting the amount of distortion. Tone: Turn left to get a bass, turn it from the center to get a middle tone, and turn it to the right to get a treble.. Level: Output settings. To make the same output as the input signal, it will be set in the direction of 10:00 to 12:00, but it also changes depending on the type of the selected diode.. Clipping mode (Toglusch)
1.Symmetrical (symmetric) LED clipping-A lot of distortion gives a sense of compression. 2. No clipping-Ideal for clean boost with open OPAMP distortion. 3. Symmetrical (non-symmetric) Silicon diode clipping-A feeling of transparent with loose distortion. In this mode, the original sound is mixed with the output sound. Customization of distortion
Base players support the rhythm and bottom that is the basics of music, tighten the overall sounds in the band, play an important role in supporting the sounds of other instruments in the ensemble, but for some reason. If there are too few pedals that have been turned out? I made this yellow base over drive for your bottom end support!. I would like to overdrive the deep part with this Blumes for guitar players who use down tuning and baritone guitars a lot.. I am looking forward to the activities with the guitar player!
We use a tube screamer all -analog soft clipping circuit, but the sound creates Blumes unique characters.. The power supply is a bipolar power supply, creating a clear, dynamics, and headrooms that all bassists will seek, and a vacuum tube amplifier can be pushed with a three -dimensional sound.. While keeping the original story character of the original story, the base player pays close attention to the response of the bass part, the bass part that is most concerned about the performance with the distortion, leaving the signal output from the base as much as possible. However, it is now possible to increase the amount of GAIN to double.. In the low setting of GAIN, the popular crunch is obtained at Plumes, and when it is raised after 12:00, the compatibility with the bass part will be the highest distortion!
The clipping mode is equipped with three kinds of clipping mode like Plumes, and can drive bass in various ways.. Mode1 is a clipping with two LEDs of Symmetrical (symmetric). It is the most distorted mode in Blumes. The sense of compression of the signal is small, open and high in output.. MODE2 is a boost mode using a clean OPAMP. You can get a simple OPAMP distortion without using a clipping diode. It is the highest output in 3 mode, and is the most wide mode of Freak -Ensight Ageless.. GAIN knob will be active as a clean boost at less than 12 o'clock. Mode3 is asymmetrical (non -symmetric) silicon diode clipping. It is the tone closest to the tube screamer, but the output is a transparent tone that provides a clear tone.. The bass in this mode is warm and round tone and the output is low.. The quality of the distortion is a mode that is closer to fuzz and gives the most comp feeling in three modes.. The output sound includes the original sound, so if you want to add a fuzz -like distortion to a clean base, you should like this mode.. Tech Specs
Dimensions: 12.065cm x 6.35cm x 6.35cm
Current consumption: 25 ma
Input impedance: 10 Mohm
Output impedance: 100 ohm
Flexi Switching: This product has a Flexi-Switch (R) function.. It is an electronic relay type True bypass, and can be used as a normal latch type switch (unlatch type) as a normal latch type switch (unlatch type).. In the case of use as a latch type switch, step on it once when you want to turn it on like a normal effector switch, and then step on the switch once again when you want to turn it off.. In the case of use as a momental switch, the effector is turned on only while stepping on the switch, and once the switch is released, it will be turned off.. Blooms uses an electronic relay type switch, so if the power is supplied, the input signal will not be output.. Power supply: Power supply This product can be used with a 2.1mm center adapter with 9V and AC adapter. We do not recommend it because noise may be used when using a power adapter that is not a daisy chain or a non -transformer system.. Also, do not use a power supply exceeding 9V as it may cause a failure!
|