ENDLESS System Inch Up Kit Racing MONO6 &Racing MONO4r Front & Rear Front and Rear Set WRX STI VAB D Type D or later EDZCXVABD
| Auction ends | 5 days |
| Bids | no |
| Current price | ¥1,078,200 $7,446 |
| Start price | ¥1,078,200 $7,446 |
| Buy-now | ¥1,078,200 $7,446 |
| Consumption tax | 10% not included |
| Seller | syarakuin +14527 |
| Condition | New |
| Start time | 2024-05-08T12:43:12+09:00 |
| End time | 2024-05-15T12:43:12+09:00 |
| Auto-prolongation | Turned off |
| Lot number | x1109541429 |
| Seller position | Saitama |
| # Product number | EDZCXVABD |
| ■ Maker | Endless/Endless |
| Product name | System inch up kit |
| ■ F / R | Front & rear front and rear set |
| ■ Automobile manufacturer | SUBARU / Subaru |
| ■ Model | WRX STI |
| Model | Vab |
| ■ Model Remarks | D-type or later |
| ■ Brake caliper item | Racing MONO6&Racing MONO4r |
| ■ Genuine rotor size (outer diameter x thickness) | FΦ340×30/RΦ326×20 |
| ■ Rotor (outer diameter x thickness) f | 370 x 34 |
| ■ Rotor (outer diameter x thickness) r | 332×30 |
| ■ Rotor Piece type (F) | 2PCS |
| ■ Rotor Piece type (R) | 3PCS |
| ■ Pad type (F) | RCP121 |
| ■ Pad type (R) | RCP147 |
| ■ About brake pads | Please select the brake pads from NEW TYPE-R / MX72 / MX72 PLUS and specify them in the remarks column when ordering. |
| ■ Product Description | * "High rigidity" and "lightweight" proved by forged mono blocks "Racingmono6" mono -block caliper that was forged by several thousand tons of pressure. Four years from conception and one year from the completion of the prototype, repeated test and race applications, and repeated specification changes resulted in a lightweight and highly rigid body that was sufficient for the competition. And the processing of a highly difficult piston cylinder is cleared by using advanced special technology. The completed body is finished by carbide aluminum processing. It is a crystal of the technology created by ENDLESS's "endless challenge", which continues to stick to forging. *The caliper body is ultra-hard anodized, and the rotor bell housing is made of tough frame coating. The caliper body of the ENDLESS monobloc series is made of ultra-hard anodized aluminum. Tofram coat is used for the rotor bell housing. As a result, it is possible to significantly reduce the discoloration of the alumite even when using a high temperature condition when driving a circuit. * Uses "e-slit", which has a high braking effect of double shaving effects The brake rotor combined with the mono -block series is an impressive "e -slit" with a long slit that draws a gentle curve and a slit of "E" lined up on a long slit. These two slits will always keep the pads optimal by demonstrating the double shaving effect, achieving further braking power. When the long slit on the rotor surface disappears and the character of E rises, it is a measure of replacement. In addition, as a result of the test on the actual car, the compatibility with Endless ceramic carbon metal brake pads are outstanding. * Forged monoblock proves "high rigidity" and "light weight" 4POT caliper version of monobloc calipers forged and molded by thousands of tons of pressure. It was completed after repeated tests in pursuit of performance such as weight reduction, durability, and heat dissipation, and repeated reviews of the shape in detail. In addition, wheels can be installed from 15 inches, and the number of wheels that can be installed has increased. And the processing of piston cylinders, which is very difficult, can be cleared by using advanced special technology. The completed body is finished by carbide aluminum processing. It is a crystal of the technology created by ENDLESS's "endless challenge", which continues to stick to forging. |
| Notes | * Rotor column 1PCS is genuine shape 1 -piece type, 2PCS is 2 -piece type, 3PCS is rear 3 -piece type. (Floating is treated as bespoke) * Comes with a size -up rotor. The attached brake rotor is an e -slit type. * If you want to know the pattern information, please check the manufacturer's official website. |
| ■ Precautions when ordering a caliper kit | ◆ ENDLESS Caliper kit Please be sure to check the compatibility of the wheel before purchasing. For genuine wheels and wheels of some manufacturers, please use the "Pattern" on the compatible table of the official website of Endless. (Matching between the genuine wheel and the brake caliper made by Endless will be difficult to install, except for a small part. ) ◆ When installing the ENDLESS caliper kit, it is necessary to process the back plate of the rotor (cutting, bending, etc.) (excluding some models). Please note. ◆ Anodizing is susceptible to continuous high-temperature conditions and ultraviolet rays due to circuit driving, etc., and may fade or peel off. For those who want to control fading and coloring as much as possible, racing alumite (caliper body) or toflam coat (bell housing only) is recommended. Also, please note that there are some different colors due to color unevenness and lots. In addition, it is not possible to apply an alumite processing again when overhaul, etc. ◆ ENDLESS Forged calipers are made of materials with high silicone content to enhance rigidity. For this reason, some color unevenness may come out due to the characteristics of alumite. In the case of the front and rear set, the color may differ before and after. Please note. ◆ The Racingmono series has a non -colored carbide aluminum processing (coloring is not possible due to the characteristics of the material used). ◆ The brake pad attached to the caliper kit can be selected. The brake pads that can be selected for each caliper are different. For more information, please see the ENDLESS official website "Caliper Kit Dedicated Repair Brake Pad List". ◆ The rotor attached to the caliper kit will be a "carving slit" specification, except for some caliper kits. * "Racingmono series" is an e -slit specification. * "CMC kit" is a drilled specification. Cannot be changed to e -slit. * "Rover mini exclusive" is an e -slit for 12inch only, and 4 pot for 10inch is drilled type. ◆ For the brake fruude used for the endless forged caliper, select the DOT4 standard or higher. ◆ Please note that the 2 -piece rotor (aluminum bell housing part) attached to the edless forged caliper and kit cannot be reprocessed in aluminum. |
| Delivery time | We will contact you after the delivery date is confirmed for the product -made product. If you are in a hurry, please check the inventory in advance. |
| ■ When ordering Notes | * This item cannot be used for cash on delivery. If you order by cash on delivery, we will check with the customer and request a change to another payment method or cancel the order. |
 |
| Time | User | Price |
| No bids | ||
